Banner SureCross DX80 Wireless Networks User Manual download pdf

DIP Switch Configurable Gateway for the M-GAGE™ Node

Features

IP67 Base

2.4 GHz

IP20 Base

900 MHz

The SureCross™ wireless system is a radio frequency network with integrated I/O that

can operate in most environments while eliminating the need for wiring runs. Systems are

built around a Gateway, which acts as the wireless network master device, and one or

more Nodes.

• Gateway’s discrete inputs are mapped to baseline two M-GAGE™ Nodes; M-GAGE

inputs are mapped to the Gateway’s outputs

• Switch configurable to allow for user programmability of two M-GAGE Nodes

• 10 to 30V dc power input

• Modbus serial interface

• Site Survey analyzes the network’s signal strength and reliability

• Frequency Hopping Spread Spectrum (FHSS) technology and Time Division Multiple

Access (TDMA) control architecture combine to ensure reliable data delivery within

the unlicensed Industrial, Scientific, and Medical (ISM) band

• Transceivers provide bidirectional communication between the Gateway and Node, in-

cluding fully acknowledged data transmission

• Lost link outputs on the Gateway

• The DX80...C models are certified for use in Class I, Division 2, Group A, B, C, D;

Zone 2 (Group IIC) Hazardous Locations when properly installed in accordance with

the National Electrical Code, the Canadian Electrical Code, LCIE/ATEX, or applicable

local codes/regulations (see Specifications)

For additional information, the most recent version of all documentation, and a complete

list of accessories, refer to Banner Engineering's website, www.bannerengineering.com/

surecross.

Models

Model Frequency Environmental Rating I/O

DX80G9M6S6P6ZP 900 MHz ISM Band

IP67, NEMA 6

Inputs: Selectable discrete

Outputs: Sourcing discrete

DX80G2M6S6P6ZP 2.4 GHz ISM Band

DX80G9M6S6P6ZPC 900 MHz ISM Band IP20, NEMA 1

Class I, Division 2, Group A, B, C, D

Hazardous Locations (see Specifica-

tions)

DX80G2M6S6P6ZPC 2.4 GHz ISM Band

Internal antenna models are also available, but are not UL Listed. For more information, contact your local Banner Engineering Corp.

representative.

WARNING: Not To Be Used for Personnel Protection

Never use this product as a sensing device for personnel protection. Doing so could lead to seri-

ous injury or death. This product does NOT include the self-checking redundant circuitry necessary to

allow its use in personnel safety applications. A sensor failure or malfunction can cause either an ener-

gized or de-energized sensor output condition.

SureCross DX80 Gateway with Discrete I/O

P/N 139075 rev. D 1/11/2012

0 139075 9

1 2 3 4 5 6 ... 10 11

Summary of Contents

Page 1 - Features

DIP Switch Configurable Gateway for the M-GAGE™ NodeFeaturesIP67 Base2.4 GHzIP20 Base900 MHzThe SureCross™ wireless system is a radio frequency networ

Page 2 - FlexPower Node

UL ListingMaximum ambient temperature: 70°CMounting instructions: See document 132607Power rating: 10 to 30V dc, UL Class 2Enclosure environmental rat

Page 3 - Wiring Diagrams

Exporting SureCross RadiosIt is our intent to fully comply with all national and regional regulations regarding radio frequency emissions. Customers w

Page 4 - DX80...C Wiring

The SureCross DX80 Wireless NetworkThe SureCross DX80 wireless I/O network provides reliable monitoring without the burden of wiring or conduit instal

Page 5 - Modbus Register Table

Wiring DiagramsM-GAGE™ Gateway I/O MappingI/O Terminal Label M-GAGE Gateway M-GAGE Node I/O1 DI1 Discrete IN 1 to Device 1, Baseline 142 DI2 Discrete

Page 6 - Device Configuration

Terminal Block (IP67 Base)PWRGNDDO6DO5DO4DO3DO2DO1PWRGNDDI6DI5DI4DI3DI2DI1DIx. Discrete IN x.DOx. Discrete OUT x.GND. Ground/dc common connection.PWR.

Page 7 - Discrete Input Type

DIxPWR or SPxSureCross DeviceDIxGNDSureCross DeviceWiring Diagrams for Discrete OutputsConnecting dc power to the communication pins will cause perman

Page 8 - Specifications

I/OPointModbus Holding Register I/O Type Units I/O Range Holding RegisterRepresentationTerminalBlock La-belsGateway Any Node Min.ValueMax.ValueMin.(De

Page 9

SwitchesDevice Settings 1 2 3 4 5 6 7 8Node 1 baseline filter ON ONNode 1: threshold = 100, hysteresis = 30 OFF* OFF*Node 1: threshold = 150, hysteres

Page 10 - Warnings

Verify CommunicationsAfter powering up and binding the Gateway and its Nodes, verify all devices are communicating properly. Verify LED 1 is green. Un

Page 11 - Contact Us

Consumption: Less than 1.4 W (60 mA) at 24V dcHousingPolycarbonateWeight: 0.26 kg (0.57 lbs)Mounting: #10 or M5 (M5 hardware included)Max. Tightening