Banner SureCross DX85 Expandable Remote I/O User Manual download pdf

Configurable Modbus slave remote I/O device with six sourcing discrete inputs and six sourcing discrete outputs

Features

IP67 Base

IP20 Base

The SureCross™ wireless system is a radio frequency network with integrated I/O that

can operate in most environments while eliminating the need for wiring runs. Systems are

built around a Gateway, which acts as the wireless network master device, and one or

more Nodes. A remote I/O device with a Modbus interface is used to expand the I/O of the

Gateway device or the Modbus host.

• Wireless industrial I/O device with six sourcing discrete inputs and six sourcing dis-

crete outputs

• 10 to 30V dc power input

• Selectable Modbus slave address

• Modbus RTU protocol using RS-485

• The DX85...C models are certified for use in Class I, Division 2, Group A, B, C, D; and

Zone 2 (Group IIC) Hazardous Locations when properly installed in accordance with

the National Electrical Code, the Canadian Electrical Code, LCIE/ATEX, or applicable

local codes/regulations (see Specifications)

Models

Model Environmental Rating I/O

DX85M6P6 IP67, NEMA 6

Inputs: Six sourcing discrete

Outputs: Six sourcing discrete

DX85M6P6C

IP20, NEMA 1

Class I, Division 2, Group A, B, C, D Hazardous

Locations (see Specifications)

WARNING: Not To Be Used for Personnel Protection

Never use this product as a sensing device for personnel protection. Doing so could lead to seri-

ous injury or death. This product does NOT include the self-checking redundant circuitry necessary to

allow its use in personnel safety applications. A sensor failure or malfunction can cause either an ener-

gized or de-energized sensor output condition.

SureCross DX85 Modbus RTU Remote I/O Device

P/N 131599 rev. G 1/10/2012

0 131599 8

1 2 3 4 5 6 7 8 9

Summary of Contents

Page 1 - Features

Configurable Modbus slave remote I/O device with six sourcing discrete inputs and six sourcing discrete outputsFeaturesIP67 BaseIP20 BaseThe SureCross

Page 2 - Additional Information

The SureCross DX80 Wireless NetworkThe SureCross DX80 wireless I/O network provides reliable monitoring without the burden of wiring or conduit instal

Page 3 - Wiring Diagrams

Wiring Diagrams5-pin Euro-Style HookupWiring the 5-pin Euro-style connector depends on the model and power requirements of the device. Connecting dc p

Page 4 - Modbus Register Table

Terminal Block (IP20 Base)DI1DI2DI3DI4DI5DI6V+V−V−DO1DO2DO3DO4DO5DO6TX/+RX/−V+DIx. Discrete IN x.DOx. Discrete OUT x.RX/-. Serial comms lineTX/+. Seri

Page 5 - Device Configuration

I/O Modbus Holding Register I/O Type Units I/O Range Holding RegisterRepresentationTerminalBlock La-belsGateway /DX85Any Node Min.ValueMax.ValueMin.(D

Page 6

3. Gently unplug the ribbon cable from the board mounted into the bottom housing. For integrated battery models (no ribbon cable) andClass I, Division

Page 7 - Specifications

SpecificationsGeneralPower*Requirements: +10 to 30V dc (For European applica-tions: +10 to 24V dc, ± 10%). (See UL section belowfor any applicable UL

Page 8 - Warnings

LCIE/ATEX: Zone 2 (II 3G / Ex nA IIC); Certificate: LCIE 10 ATEX 1012 X UL ListingMaximum ambient temperature: 70°CMounting instructions: See document

Page 9 - Contact Us

Banner Limited WarrantyThis Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SH