Banner RP-QM90 Rope Pull Switch User Manual download pdf

Datasheet

•

Positive-opening safety contacts (IEC 60947-5-1), not dependent

upon springs

• Contacts latch open when rope is pulled; requires manual reset

• Heavy-duty die cast metal housing, rated IP65, suitable for demanding

industrial environments

• Rope spans up to 100 m (330 ft), with the switch mounted in the center

of the span

• Both safety contacts are closed with normal rope tension, and open when

rope is pulled or if rope breaks (or if tension is reduced from normal

amount)

• Extra contacts for monitoring or to provide dual-channel input to a safety

module

• Switch actuator position clearly indicates when rope has proper tension

for operation

• Long life, switch rated at 1 million mechanical operations, minimum

•

Protective Earth Terminal (IEC 60947-1)

Model

Max. Overall

Rope Length

Run Position Cable Pulled

(either side)

Cable Break

(either side)

Switching Diagram

RP-QM90F-100L 100 m (330 ft)

23 24

11 12

23 24

11 12

23 24

11 12

23 24

11 - 12

23 - 24

40°

30°

Lock

70N

Lock

Lever

11 - 12

23 - 24

RightLeft

Contacts: Open Closed

NOTE:

This symbol for a positive-opening safety contact (IEC 60947-5-1) is used in the switching

diagram to identify the point in actuator travel where the normally-closed safety contact is fully open.

Important... Read This First

Regarding the Use of Rope Pull Switches. In the United States, the functions that Banner rope pull switches are

intended to perform are regulated by the Occupational Safety and Health Administration (OSHA). Whether or not any

particular rope pull switch installation meets all applicable OSHA requirements depends upon factors that are beyond the

control of Banner Engineering Corp. These factors include the details of how the switches are applied, installed, wired,

operated, and maintained.

Banner Engineering Corp. has attempted to provide complete application, installation, operation, and maintenance

instructions in this document. Direct any questions regarding the use or installation of rope pull switches to the factory

applications department.

RP-QM90 Series Rope Pull Switches

P/N 62086 Rev. D 4 February 2014

62086

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - Datasheet

Datasheet• Positive-opening safety contacts (IEC 60947-5-1), not dependentupon springs• Contacts latch open when rope is pulled; requires manual reset

Page 2 - Overview

Banner Engineering Corp. recommends that rope pull switches be applied according to the guidelines set forth in thestandards listed below. In addition

Page 3 - Mechanical Installation

Figure 1. Run Position: Proper Rope TensionFigure 2. Rope Pulled: Contact Pairs 11-12 OpenFigure 3. Rope Break or Slack: Contact Pairs 11-12 OpenMecha

Page 4 - Electrical Installation

All hardware is supplied by the user. The switch mounting holes are on a standard limit switch mounting pattern of 30 x 60millimeters, and accept M5 (

Page 5 - Specifications

Maintenance/CheckoutAt switch installation or replacement and at machine set up, a Designated Person1 must test each switch for propermachine shutdown

Page 6 - Accessories

Dimensions11 1223 2411 1223 24206 mm(8.10") 10.0 mm(0.39")58 mm(2.33")24.5 mm(0.97")125 mm(4.90")137 mm(5.40")186.0 mm(7

Page 7 - Pull ring

One conduit adapter is supplied with each switch.Components for the Wire Rope Assembly112311 1223 24Pull ringto resetThimble ClampPulleyTensioning Spr

Page 8

Model Quantity Description Tensioning SpringRPA-S1-1 1 Tensioning spring #1Model Quantity Description Tensioning SpringRPA-S2-1 1 Tensioning spring #2

Comments to this Manuals

No comments

Banner RP-QM90 Rope Pull Switch User Manual

Browse online or download User Manual for Special machinery Banner RP-QM90 Rope Pull Switch. Banner RP-QM90 Rope Pull Switch User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Special machinery Banner RP-QM90 Rope Pull Switch