Banner Q45 Series User Manual download pdf

Q45XDN

“Intelligent” Photoelectric Sensors for use on DeviceNet

™

Bus Networks

Printed in USA 05/03 P/N 46655 rev. C

• Easy “smart sensor” interfacing to DeviceNet bus networks

• Integral Euro-style (M12) quick-disconnect connector for DeviceNet compatible cable

• Impressive optical performance in opposed, diffuse, retroreflective, convergent or

fiber optic sensing modes

• Highly visible Power and Received Signal Strength indicator LEDs

•Tough mechanical design

Description

Q45XDN Series sensors are designed specifically for use on DeviceNet-bus

networks. These are “smart” sensors which can be wired to a DeviceNet bus using

a “dumb” tee.

Q45XDN1 models support the Bit Strobe Connection, which responds to a master’s

request. Q45XDN2 models support the Change of State Connection, which responds

to a slave’s change of state. All models support the Explicit Message Connection,

which is required to Set and Get sensor Attributes.

Q45XDN Series sensors feature two highly-visible sensor status indicator LEDs for

power and received signal strength. The Signal indicator incorporates Banner’s

patented

†

Alignment Indicating Device (AID

™

) circuitry which pulses the indicator at a

rate which is proportional to the received light signal strength. A slow flash rate alerts

personnel to a marginal signal due to sensor misalignment or dirt on the lenses.

Q45XDN Series photoelectric sensors have impressive optical performance (see

excess gain curves on pp. 2 - 4). All models boast o-ring sealing which exceeds the

NEMA 6P (IP67) rating. They are extremely rugged, with PBT polyester housings and

molded acrylic lenses. They are equipped with a 12 mm Euro-style quick-disconnect

connector which accepts DeviceNet-compatible cable (see Hookup Information).

†

U.S. Patent #4356393

Features

™

WARNING . . .

Not To Be Used for Personnel Protection

Never use this product as a sensing device for personnel protection. Doing so could lead to serious injury or death.

This product does NOT include the self-checking redundant circuitry necessary to allow its use in personnel safety

applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Consult your

current Banner Safety Products catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection.

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - Features

Q45XDN“Intelligent” Photoelectric Sensors for use on DeviceNet™ Bus NetworksPrinted in USA 05/03 P/N 46655 rev. C• Easy “smart sensor” interfacing to

Page 2 - Retroreflective Mode Models

Q45XDN 2 P/N 46655 rev. C™Banner Engineering Corp. • Minneapolis, MN U.S.A.www.bannerengineering.com • Tel: 763.544.3164Infrared, 880 nmPVisible Red,

Page 3 - Convergent Mode Models

Q45XDNP/N 46655 rev. C 3™Banner Engineering Corp. • Minneapolis, MN U.S.A.www.bannerengineering.com • Tel: 763.544.3164Infrared, 880 nmVisible Red, 68

Page 4 - Plastic Fiber Optic Models

Q45XDN 4 P/N 46655 rev. C™Banner Engineering Corp. • Minneapolis, MN U.S.A.www.bannerengineering.com • Tel: 763.544.3164Glass Fiber Optic ModelsQ45XDN

Page 5 - Specifications

Q45XDNP/N 46655 rev. C 5™Banner Engineering Corp. • Minneapolis, MN U.S.A.www.bannerengineering.com • Tel: 763.544.3164SpecificationsAdjustments Multi

Page 6 - Dimensions

DimensionsQ45XDN 6 P/N 46655 rev. C™Banner Engineering Corp. • Minneapolis, MN U.S.A.www.bannerengineering.com • Tel: 763.544.3164See tableat left50.8

Page 7 - Mounting Brackets

Q45XDNP/N 46655 rev. C 7™Banner Engineering Corp. • Minneapolis, MN U.S.A.www.bannerengineering.com • Tel: 763.544.3164Mounting BracketsSMB30S SMB30C•

Page 8 - P/N 46655 rev. C

Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengi